感謝您使用我們的產品！
Thank you for using our products！


打開產品以后請檢查配件，配件如下：
After opening the product, please check the accessories as follows:

控制器連接方式：
Controller connection：

1、電 源 線——接入220V /  110V 電源
Power cord——Access 220V / 110V power supply 

2、喇叭接口——連接喇叭/音箱
Speaker interface——Connect the speaker 

3、紅外線接口—連接紅外線開關
Infrared interface——Connecting infrared switch 

4、數據傳輸——連接產品（腿上的電纜線插頭）
Data transmission——Connectivity products (leg cable plug)

控制器說明：
Controller description：

1、電 源 線——給控制器、產品供電
Power cord - provide power to the controller, the product 

2、電源開關——控制整個控制器電源（紅色按鈕）
The power switch - control the entire controller power (red button) 

3、音箱接口——給產品提供叫聲
Speaker interface - Connect the speaker and provide sounds 

4、紅外線接口—啟動產品所有功能（有效距離90°，5米）
Infrared switch - Start all functions (effective distance of 90 °, 5 m) 

5、數據線接口——控制器與恐龍之間連接，傳輸數據。
Data Transfer code- transfer data between the controller and the dinosaur. 

6、電源指示燈——點亮以后表示控制器已經通電。
Power sign - Expansion slot - Control box is ready to use when light is on 

操作說明：
Instructions: 

1、電源線與控制器連接，檢查電源是否通電。
The power cord is connected to the controller, check whether the power supply is powered. 

2、檢測紅外線開關、音箱、數據線是否接好。
Detecting infrared light switch, speaker, data line is connected. 

3、打開控制器電源開關。
Turn on the controller power switch. 

4、調整好聲音大小。
Adjusting the size of a good voice. 

5、在紅外線探頭有效距離內晃動一下，此時紅外線探頭燈亮起，產品開始工作。一個程序執行完畢后產品會自動停止（一般30-40秒，時間長短可設置）；紅外線探頭需再次感應才能繼續工作（紅外線開關是控制產品啟動開關，當觀眾在紅外線探頭范圍5米內運動，紅外線開關自動啟動，同時控制器會按程序通過數據線把信號傳輸給恐龍，恐龍就會啟動）。
Shaking once within the effective distance of the infrared probe , infrared probe lights at this time, the products begin to work. The product will automatically stop after a program execution (generally 30-40 seconds, the length of time can be set); infrared probes need to re-induction can continue to work (infrared switch control products start switch when the visitors move in the the infrared probe in 5 meters, the infrared switch automatically starts at the same time, and the controller transfer signal to the dinosaurs through a data line, then dinosaur starts). 

6、假山內部是空的，用來隱藏控制器及喇叭/音箱。紅外線探頭必須留在外面能讓觀眾感應到的范圍。
The rockery is empty inside ,which is used to hide the controller and speaker. The infrared probe must stay outside make the infrared can sense audience .